Services

Complete Chimney Services, Start to Finish

Sales, manufacturing, fittings, installation, servicing, repair, custom work and fresh air systems — each handled by the same team that fabricates the ducting.

Chimney Sales Chimney Manufacturing Chimney Fittings Chimney Installation Chimney Servicing Repair & Maintenance Custom Chimney Solutions Duct & Fresh Air Systems

01 — Service

Chimney Sales

We supply commercial kitchen chimneys, canopy hoods, baffle filters, axial and centrifugal exhaust units and the fittings that go with them. Sizing is worked out from your kitchen layout, the equipment under the hood and the discharge route, so what you buy matches the job rather than a catalogue number.

Key benefits

Sized for your kitchen and equipment load
Stainless steel and galvanised options
Hoods, filters, fans, blowers and accessories
Guidance on the right unit before you buy

Suitable for

Hotels and restaurants
Bakeries and sweet stalls
Canteens and messes
Small industrial units

Enquire About Sales WhatsApp

02 — Service

Chimney Manufacturing

Ducting is fabricated in our workshop from stainless steel and galvanised sheet — straight runs, radius elbows, square-to-round transitions, weather cowls and canopy hoods, all cut and formed to the dimensions taken from your site. Making the parts ourselves means an awkward corner or a low ceiling is handled at the fabrication stage instead of on site.

Key benefits

Made to site measurements, not stock sizes
Stainless steel and galvanised sheet
Radius elbows, transitions, cowls and hoods
Awkward layouts handled in fabrication

Suitable for

Custom canopy hoods
Duct runs and risers
Discharge cowls and weather hoods
Replacement sections

Enquire About Manufacturing WhatsApp

03 — Service

Chimney Fittings

Fitting is where an exhaust system is made or lost. We set out the duct route, fabricate and fit the sections, support them properly off the slab or wall, seal the joints and terminate the run cleanly. The route is planned so filters, access panels and the motor stay reachable once the kitchen is running.

Key benefits

Planned duct route before work begins
Properly supported and sealed joints
Access kept for later cleaning
Neat finish in visible areas

Suitable for

Overhead duct routing
Vertical risers and shafts
External wall runs
Hood-to-duct connections

Enquire About Fittings WhatsApp

04 — Service

Chimney Installation

We handle the full installation: mounting the hood at the right height over the range, running the duct, setting the blower or exhaust fan on its base, wiring it to your point and terminating the discharge above roof level. Work is planned around your kitchen so a running business loses as little time as possible.

Key benefits

Hood set at the correct working height
Blower mounted on a proper base
Discharge terminated above roof level
Planned around your kitchen hours

Suitable for

New commercial kitchens
Kitchen expansions
Rooftop blower installation
Exhaust system replacement

Enquire About Installation WhatsApp

05 — Service

Chimney Servicing

Grease build-up in the hood, filters and duct is what quietly kills suction and raises the fire risk in a commercial kitchen. Servicing covers cleaning the hood and baffle filters, clearing the duct run, checking the blower, belt and bearings, and setting the unit back to work properly.

Key benefits

Hood, filters and duct cleaned
Blower, belt and bearings checked
Suction restored across the line
Lower grease and fire risk

Suitable for

Hotels and restaurants
Industrial canteens
Scheduled periodic cleaning
Pre-inspection clean-ups

Enquire About Servicing WhatsApp

06 — Service

Repair & Maintenance

Weak suction, noise, vibration or a motor that trips usually has a specific cause — a choked duct, a slipping belt, a worn bearing, an undersized fan or a badly routed run. We look at the whole system rather than swapping parts, repair or replace what has failed, and tell you plainly if the design itself is the problem.

Key benefits

Fault traced across the whole system
Motor, belt and bearing replacement
Duct repair and re-routing
Works on systems we did not install

Suitable for

Weak or uneven suction
Noise and vibration
Damaged or leaking ducts
Motor and blower faults

Enquire About Repair & Maintenance WhatsApp

07 — Service

Custom Chimney Solutions

Not every kitchen or shed fits a standard solution. Low slabs, shared walls, long horizontal runs, multiple hoods on one discharge, or an exhaust requirement outside a kitchen altogether — these are worked out from site measurements, fabricated to suit and fitted as one system.

Key benefits

Site survey and measurement first
Fabrication built around the constraint
Multiple hoods on a single discharge
Industrial and non-kitchen exhaust

Suitable for

Tight or low-ceiling kitchens
Multi-hood layouts
Long external duct runs
Industrial exhaust and ventilation

Enquire About Custom Solutions WhatsApp

Fresh air duct with grille outlets fitted below a kitchen ceiling

Fresh air duct run and supply grilles across a commercial kitchen ceiling

08 — Service

Duct Fresh Air & Fresh Air Fan Systems

Pulling stale air out is only half the job — a kitchen also needs clean air coming back in. We manufacture and fit fresh air ducting, fresh air fans and filter units, so replacement air reaches the cooking line instead of being dragged in through doors and windows.

What we handle

Fresh air duct fabrication and routing
Fresh air fan supply and fitting
Fresh air filter units and grilles
Balanced supply against exhaust load

Suitable for

Enclosed and basement kitchens
Hotels, canteens and restaurants
Kitchens with heavy exhaust load
Workshops and production halls

Enquire About Fresh Air Systems WhatsApp

What we supply

Hoods, Fans and Blower Units

Units are recommended against your kitchen layout and load. Sizes and finishes are confirmed at enquiry stage.

Canopy Hood with Baffle Filters

Stainless canopy hood with baffle filters and control panel, sized to the cooking line.

Compact Wall-Mounted Hood

Smaller wall hood for tea shops, bakeries and compact kitchens.

Axial Flow Exhaust Fan

Cased axial fan for straight-through extraction and general ventilation.

Assembled Fan & Blower Units

Fan and blower assemblies prepared in our workshop before installation.

From our sites

Work Photographs From Recent Jobs

Manufacturing, ducting, installation, servicing and cleaning work photographed on site. Click any picture to open it larger — the first card is a short video from one of our jobs.

Technicians installing a rooftop blower unit

Start a conversation

Looking for a Reliable Chimney Solution?

Talk to Sri Vinayaga Chimney Work about your chimney sales, manufacturing, fitting, installation or servicing requirement. Send us the details and we will get back to you.

Send an Enquiry WhatsApp Us